Back to Vacuums

Cyclonic Separator Steel Pail Lid

$99.95

  • Ready to use out of the box
  • Includes lid with deflectors
  • Cyclonic Deflectors are mounted on modified steel pail lid
  • Includes gasket ring
  • Hard plastic deflectors.  Use either hole for inlet or outlet. 
  • Made for standard 2-1/2″ shop vacuum hose adapters.
  • Made for wet/dry operation
  • Will handle gravel up to 1-1/2″

 

2 in stock (can be backordered)

Description

This Cyclonic Separator Steel Pail Lid fits standard 5 and 7 gallon steel pails.

Cat 6 Tools is now offering a new Commercial Grade Cyclonic Separator Steel Pail Lid.  This modified steel pail lid will fit standard 5 or 7 gallon steel pails.  As a result, this lid is made to handle nasty stuff.  Consequently, when the bucket is full just remove the lid, and seal with a standard steel pail lid for sealing in the bad stuff for easy carry away. In addition, when the pail wears out, just replace with any standard 5 or 7 gallon steel pail.  Furthermore, this steel pail cyclonic separator lid works with standard shop vacuums with 2-1/2″ hoses.

You get what you pay for

The old saying, you get what you pay for applies to this Commercial Grade Cyclonic Separator steel pail Lid. As a result of engineering design, this steel pail lid is tough and durable and and outperforms the inexpensive kind made for saw dust.  The hose deflectors are made for wet or dry nasty stuff. For instance, they will handle anything from 1-1/2 inch gravel to raw sewage.    Consequently, this is the one of the most rugged cyclonic lids available.  In addition, the deflector hose adapters are universal, so you can use either for inlet or outlet.

Replaceable Parts

All the hardware on this cyclonic lid are replaceable. The lid is coated with a rust inhibitor.  The deflectors are universal and are easy to replace with just three screws.

5-gal-cyclonic-separator-steel pail-lid-top
Cat 6 Tools 5 gallon steel pail cyclonic separator lid top showing inlet and outlet ports. Both ports are usable as inlet or outlet.

 

5-gallon-cyclonic-separator-steel-pail-lid-underside
Underside of 5 gallon steel pail cyclonic separator lid

 

Fits standard 5 or 7 gallon steel pail

The cyclonic separator steel pail lid fits most 5 and 7 gallon steel pails.  The Cat 6 Tools Cyclonic Separator Steel Pail

is shown below.

cyclonic-separator-steel-pail-5-gallon
Cyclonic Separator Steel Pail – 5 gallon

The Flood Buddy

When your dwellings are flooded and clean up begins, use the Flood Buddy – Commercial Grade Cyclonic Vacuum Bucket to do the dirty work.   In other words, keep the muck out of your shop vacuum, use this Cyclonic Vacuum Steel Pail  as a pre-filter.  It removes 98% of all the water, mud, dirt, or dust allowing easy cleaning of your shop vacuum. In addition, this Cyclonic Pail was tested with the Ridgid WD19560 vacuum and the results were outstanding.  The Cyclonic Separator Steel Pail will work with any vacuum, however the higher the suction rate and flow rate the better.  Just make sure the inlet uses a 2-1/2″ hose.

Save your back

Shop vacuums are extremely difficult to empty of heavy debris.  The 7 gallon buck and handle make lifting easy and dumping just as easy.   In addition, cleaning buckets is a lot easier than cleaning out shop vacuums.  They are easy to dump and easy to wash out.

 

cyclonic-separator-7-gal-steel-pail-and-ridgid-shop-vacuum
Cyclonic Separator 7 gallon Steel Pail attached to Ridgid Shop Vacuum

It works with all 2-1/2″ shop vacuum hoses

This Bucket lid has two deflector connectors, one for hooking to your shop vacuum using the 4 foot hose that comes with the unit, and one for your vacuum hose.  The deflector plate attaches to a modified Gamma Lid.   This lid will screw onto any 5 or 7 gallon bucket fitted with a gamma adapter.  Everything is replaceable.

Cleaning up hazardous materials

Save your back and your your shop vacuum when sucking up really bad stuff.   Because it works wet or dry, this Cyclonic Separator Steel Pail Lid works in almost any environment.  As a result of heavy duty construction, when your bucket is full, remove the deflector lid and replace with a standard steel pail lid.  This lid seals in the nasty stuff for easy transport and disposal.

Made in the USA

Cat 6 Tools is proud to attach this sticker to tools that we modify, fabricate and assemble in the USA.

cat-6-tools-patent-pending-made-in-usa
Products made by Cat 6 Tools, LLC that are made, assembled, modified in the USA

We’re here to help

Contact us at:

Cat 6 Tools, LLC
Cat 6 Tools, LLC
Henderson, NV
info@cat6tools.com
702-533-4363

Additional information

Weight 3 lbs
Dimensions 14 × 14 × 6 in